Data Center Decommissioning in Des Moines
Des Moines Data Center Planning

Data Center Decommissioning in Des Moines

Retiring a Des Moines server room or data hall in waves? Precision E-Cycle scopes each release wave with your team, offers free pickup for qualifying business volumes, and logs serial information at intake in Lincoln.

Rack servers, blade chassis, and SAN, NAS, and DAS storage arrays sorted by release wave.
Switches, routers, firewalls, and security appliances treated as storage-bearing equipment.
Tape libraries, backup systems, UPS, power distribution, and cooling units your team has released.
A data decision for each array, drive group, and tape set, with methods informed by NIST SP 800-88 Rev. 2.
Pickup and serial logging at intake at Precision's Lincoln facility.
Routing of applicable material to R2-certified downstream processors, with certificate fields agreed in project review.

What Does Data Center Decommissioning Cover for a Des Moines Team?

Data center decommissioning in Des Moines is the planned retirement of a server room or data hall: its servers, storage arrays, network gear, and released UPS and cooling units, with a data decision for every storage device. Precision E-Cycle picks up the released equipment and processes it at its only facility, in Lincoln, Nebraska.

For a Des Moines data center manager, the hard part is rarely the server count. A hall usually empties in waves while workloads migrate, and each wave carries data in less obvious places: array shelves, tape cartridges, and switches holding configurations. Every wave needs its own release list before anything leaves a rack.

What a wave-based decommission gives a Des Moines infrastructure team

Storage counted in every rack

Arrays, tape sets, and network devices each get their own data decision, so nothing that holds data is counted only as hardware.

An intake record you can reconcile

Serial information logged at intake in Lincoln can be compared line by line with each wave inventory at closeout.

One security standard behind the process

Precision E-Cycle holds ISO/IEC 27001:2022 for information security management, and each storage decision stays with your policy owner.

Request Service

Ready to Recycle?

Pickup is free for qualifying business volumes. Schedule yours or contact us with questions.

Prefer to call?

Monday through Friday, 8:00 AM to 5:00 PM, Central time.

402-540-6965
How It Works

How a Des Moines decommission runs, wave by wave

01

Inventory the hall by release wave

List servers, arrays, network devices, tape, and UPS or cooling units by category and rack, then group them into the waves your team plans to release. Give every line an owner, quantity, condition, and available identifier.

02

Settle the data decision for each wave

Your organization categorizes the data on each array, drive group, tape set, and network device and decides whether media will be reused or retired. Precision matches its methods to media type, informed by NIST SP 800-88 Rev. 2.

03

Confirm scope in project review

Agree the accepted categories, the pickup plan for each wave (free pickup), the certificate fields and format, and any pricing or buyback terms before a wave is released.

04

Pickup, intake, and downstream routing

Released equipment is picked up in the Des Moines area and taken to Lincoln, Nebraska, where serial information is logged at intake and applicable material is routed to R2-certified downstream processors.

Which Equipment in a Des Moines Data Hall Belongs on the List?

Sort every rack in a Des Moines data hall against Precision E-Cycle's accepted server and data center categories before any line enters the scope. Record each category separately, even when it shares a rack, so storage, network, and power equipment each keep an owner, a quantity, a condition, and an available identifier.

Rack servers (1U through 10U) and blade chassis
Count by model and rack, and note whether drives are still installed.
SAN, NAS, and DAS arrays
List each array and its drive shelves as separate storage lines.
Switches, routers, firewalls, and security appliances
Treat each device as storage-bearing and give it a data decision.
Tape libraries and backup systems
Count cartridges apart from the library chassis they sit in.
UPS, power distribution, and cooling units
List only units your facilities team has already disconnected and released.

Check a rack against the full accepted equipment list

Accepted items that are easy to miss

  • Patch panels and cabling accessories pulled from the racks.
  • LTO and other magnetic tape media stored beside the library.
  • Loose NVMe, M.2, and other drives kept as spares.
  • RAID arrays and enclosures outside the main storage rows.

Empty racks, raised floor panels, and building fixtures are not on the published list. Hold them on a separate line and raise them in the project review rather than assuming they travel with the equipment.

Networking gear holds data too

NIST SP 800-88 Rev. 2 counts networking devices as information storage media, alongside hard drives, solid state drives, and magnetic tape. In a decommission, that puts core switches, routers, and firewalls on the data list as well as the hardware list, each with an owner who decides how its configuration is handled.

Plan the hall in release waves

Few data halls empty in a single move. Group racks into release waves that follow the migration plan, and give each wave its own list, release owner, and data decision. A wave is ready for project review only when every line in it has an owner and a status.

  • Workloads on the wave's servers have moved or been retired.
  • Backups and retention holds tied to the wave are cleared.
  • A named owner can release every rack in the wave.
  • Unlisted items sit on a separate line until reviewed.

Agree who does the physical work

Settle in the project review who handles power shutdown, cooling changes, and removal of equipment from racks, and in what order. Raise access or escort rules for each wave at the same time.

Key takeaway

Data center managers reviewing a decommission usually expect one list per release wave, with storage, network, and power lines kept apart.

How Should Storage Be Decided Before a Des Moines Data Hall Goes Dark?

Decide storage group by group, before release, using your data policy with NIST SP 800-88 Rev. 2 as the reference. The standard treats reuse as a key sanitization decision, asking whether media is "planned for reuse (e.g., internal transfer, donations, refurbishment)." Precision E-Cycle applies data destruction methods informed by that guidance, matched to media type and data sensitivity.

Check the policy before the first wave. NIST SP 800-88 Rev. 2 says a storage sanitization policy should address requirements for the disposal or reuse of storage assets and the documentation of sanitization activities. If yours is silent on either, settle it with your security owner before storage decisions are recorded.

  • Categorize the data each array, drive group, and tape set held.
  • Mark which media is planned for internal reuse and which is retiring.
  • Record the method your policy owner approves for each group.
  • Flag leased equipment that must go back to a lessor.

Arrays that held data for many tenants

Shared arrays raise a specific question. NIST SP 800-88 Rev. 2 uses a data center device holding several customers' data as its example of partial sanitization, then says "sanitization of the whole ISM is preferred to partial ISM sanitization whenever possible," where ISM means information storage media. When an entire array is retiring, plan for the whole device.

Media planned for internal reuse
Needs a method that leaves the device usable, chosen by your policy owner.
Media retiring for good
NIST notes destruction can be the simplest method when media will not be reused.
Media with an unknown history
Handle it at the highest sensitivity in its wave until an owner decides otherwise.

Match method to sensitivity

NIST SP 800-88 Rev. 2, section 3.1, says pulverize and shred techniques should be avoided for anything but the lowest security categories of data. Precision matches the method to the media type and your data sensitivity rather than treating every device alike.

Leased hardware needs its data decision early. NIST SP 800-88 Rev. 2 notes that media control changes when equipment is returned from a leasing agreement or sent to a recycling facility, so settle sanitization for leased arrays and servers before the return is arranged.

Must media be destroyed before it leaves the site? Read about Des Moines on-site destruction

Self-encrypting arrays and cryptographic erase

Many newer arrays and drives encrypt data at rest. NIST SP 800-88 Rev. 2 says that under the correct conditions and with strong cryptography, cryptographic erase is a purge technique, because sanitizing the keys sanitizes the data. Whether it fits your arrays is a decision for your security owner, recorded before release.

Key takeaway

Record every storage decision before its wave is released, with the method matched to the data the media held.

How Does a Des Moines Decommission Move from Project Review to Closeout?

A Precision E-Cycle decommission starts with a project review that sets accepted categories, the pickup plan for each wave, and the certificate fields your organization needs. Released equipment is then picked up and taken to Lincoln, Nebraska, where serial information is logged at intake and applicable material is routed to R2-certified downstream processors.

Your team, before pickup
Inventory by wave, release authority, data decisions, retention holds, and the power and cooling shutdown sequence.
Precision E-Cycle, after release
Pickup, serial logging at intake in Lincoln, destruction methods informed by NIST SP 800-88 where the agreed scope includes them, and downstream routing.

What to send before the project review

  • Equipment categories and estimated quantities for each release wave.
  • Storage groups in each wave and the data decision recorded for each.
  • Leased equipment and any lessor return requirements.
  • Site access notes such as dock, elevator, and security escort needs.
  • The name of the person who can release each wave.

How pickup is scoped for a Des Moines data hall

Organizations in Des Moines, West Des Moines, and elsewhere in Polk County schedule pickup, processed at Precision E-Cycle's secure Lincoln, Nebraska facility. The project review plans each release wave and how its pickup is arranged.

Financial services and healthcare shape much of the metro's infrastructure across Des Moines and West Des Moines, where multi-site organizations often release data hall hardware in waves across downtown and suburban buildings.

Set closeout fields before the first wave ships

Per NIST SP 800-88 Rev. 2, a completed certificate of sanitization should record details such as manufacturer, model, serial number, media type, method, and verification method. Use that list to decide which fields your team needs, then agree in the project review which fields and format Precision's certificate carries, along with pricing and any buyback terms.

  • Compare intake serial information with each wave list.
  • Flag lines that were added, removed, or reclassified.
  • Check that each storage group shows the agreed method.
  • Keep open exceptions visible until an owner resolves them.

Planning closeout records? See Des Moines certificates of destruction

Which certifications Precision E-Cycle holds

Precision E-Cycle holds ISO/IEC 27001:2022 for information security management, along with ISO 14001, ISO 9001, and ISO 45001. These are management system certifications. They do not certify anyone against NIST or settle a customer's own legal obligations.

ISO/IEC 27001:2022
Information security management system.
ISO 14001:2026
Environmental management system.
ISO 9001:2015
Quality management system.
ISO 45001:2018
Occupational health and safety management system.

Key takeaway

A decommission closes when every wave list, intake record, and storage decision agree, with any open item named and owned. Request a free quote to plan your first release wave.

FAQ

Data Center Decommissioning Questions from Des Moines Teams

Include rack servers (1U through 10U), blade chassis, SAN, NAS, and DAS arrays, switches, routers, firewalls, tape libraries, backup systems, UPS and power distribution units, and cooling hardware. Those are the data center categories on Precision E-Cycle's accepted list. Anything else in the room stays on its own line until the project review confirms it.
Before anything is disconnected, confirm that workloads have moved, backups and retention holds are cleared, and a named person can release each wave. Record which arrays, drives, tape sets, and network devices hold data and which decision applies to each. Agree in the project review who sequences power shutdown, cooling changes, and removal from racks.
Decide storage one group at a time. NIST SP 800-88 Rev. 2 asks organizations to categorize the information, assess the media, and weigh future plans, including whether media is planned for reuse, before choosing a method. Precision E-Cycle applies methods informed by that guidance and matched to media type and data sensitivity, as agreed in the project review.
A shared wave list does most of the work. For each wave, record the racks and equipment categories, quantities, the owner who can release them, the data decision for each storage group, and site access notes for pickup. Name who owns the power and cooling sequence and who owns release and data decisions.
Expect a record that ties the serial information Precision E-Cycle logs at intake in Lincoln to your approved wave inventory, with exceptions noted. Certificate fields and format, pricing, and any buyback terms are agreed in the project review. Reconcile the returned record against each wave list before you close the project.

Request Service

Ready to Get Started in Des Moines?

Get a free quote or send us a message about your project, and we scope pickup and documentation around your site.